Daystate Wolverine

New

Regulator with vented to atmosphere, but without drilling in the tank. Simple installation. just uscrew the air tube from airgun body..

 89.00 USD

More details

79,00 €

- +

  • High precion of regulation

  • Unique technologic solution

  • You buy directly from the manufacturer

  • 2 years warranty

  • Free shipping all over the world

  • Reviews
  • Video
  • Instruction
  • Results
  • Volume discounts

No customer comments for the moment. Login

Write a review

Daystate Wolverine

Daystate Wolverine

Regulator with vented to atmosphere, but without drilling in the tank. Simple installation. just uscrew the air tube from airgun body..

 89.00 USD

Write a review

!!!Dont forget turn on NOTE in youtubevideo. This notes are important for the correct installation , so you can  avoid frequent mistakes !!!

Video Installation:

Correct clean air tube and regulator

How to find out proper function of regulator.

Setting output pressure on regulator

What to do when your output pressure increasing over time? This is most likely caused by dirt on o-ring on plastic screw.

In this video is shown how remove dirt and replace o-ring . In video is used Gunpower regulator. Procedure is same for others regulator.

It is appropriate before reading the instructions look at the video instructions and then read the instructions for avoiding common mistakes during installation

Daystate Wolverin

1)      Unscrew airtube + cleaning

2)      Mount regulator

3)      Filling and draining air

4)      Seting regulátor

5)      Shipment contains

1)      Drain all air from airtube. Remove coupling between airtube and barel.Unscrew airtube from airgun and clean o-ring and inside of the airtube. For cleaning we use a foam or lint free cloth. It is good to wash out the inside of the airtube with degreaser, or technical petrol, etc..

2)      Remove the O-ring from plug. Spray regulators o-ring from outer side with silicone spray. Insert regulator into airtube so that it is possible to screw the brass plug and check the presence of the lower O-ring in the groove. By screwing plug we get regulator into correct position. Dont screw plug to the max, but leave a gap (between plug and airtube) about 0.5 mm

3)      Fill airtube with air through quick fill. After proper installation should gauge on airgun show regulated pressure, for the filling  always use a filling set with an external gauge, so that you have an overview of the real pressure in the airtube.

4)      The pressure setting is done by using a flat screwdriver in the upper part of the regulator.  When we setting regulator we rotate with  inside plastic screw with groove. The output pressure is showed by location colored grooves on the inner plastic screw. The total rotation range of the output pressure is in the range from 100 to 150 bar and is approximately 3/4 turn.

Scale is starting on 100 bar (green color) and ends on 150 bar (red color). Scale is only approximate and course times may change slightly due to fatigue disc springs. Fill the airtube to the maximum pressure which is mentioned by manufacturer.

5)  Regulator

2 spare o-rings.

Wolverine regulator set on 155 bar    5.5mm  pellets 1.18g

Regulator used with different screw on striker ( for limited operation length of the firing pin )

Altaros daystate woverine regulator results

Wolverine regulator set on 170BAR 5.5mm   pellets 1.65g monster

Regulator used with different screw on striker ( for limited operation length of the firing pin )

Altaros daystate woverine regulator results

Wolverine compared with and without regulator   .22   pellets 1.65g

Altaros daystate woverine regulator results comapred

Wolverine new bolt to hammer for more  limited  travel

New wolverine bolt

Wolverine new bolt ( this bolt is sent with regulator )

New wolverine bolt

Great video from Gregor about Wolverine 303. 30 caliber with/without regulator and other modification

Results from Gregor:

Daystate Wolverine 303 Unregulated JSB .30 - 50,15 grain

Daystate Wolverine 303 Regulated 155 bar - JSB .30 - 50,15 grain Modified

Daystate Wolverine 303 Regulated 170 bar - JSB .30 - 50,15 grain

Quantity Discount You Save
2 -1 731,00 € Up to -3 462,00 €

Product options note

These data is only information for us, not mandatory values. For example, if your rifle is currently set on 16J, then you can not with regulator expects higher energy than 16J. The regulator can never increase energy!

For more information, please read FAQ section or contact us by e-mail.

Output pressure we set according to requirements the power rifle with the regulator. If you want a specific output pressure so indicate that in notes for orders.

If you do not know any product options, or you are unsure so please state this in the notes for orders.

Product Options
Full name of airgun model
Full name of airgun model    * Required
Full name 
 
 
* Required
Airgun model
Airgun model    * Required
 
US
 
 
UK
 
 
EU
 
 
AUS
 
 
ASIA
 
Caliber
Caliber    * Required
 
.177 /4.5mm
 
 
.20 /5.0mm
 
 
.22/5.5mm
 
 
.25/6.35mm
 
 
.35/ 9mm
 
Actual measured energy or energy given by the manufacturer
Actual measured energy or energy given by the manufacturer    * Required
 
7,5J / 5,5 ft/lbs
 
 
12J / 9 ft/lbs
 
 
16J / 12 ft/lbs
 
 
21J / 15,5 ft/lbs
 
 
27J / 20 ft/lbs
 
 
33J / 24 ft/lbs
 
 
40J / 30 ft/lbs
 
 
45J / 33 ft/lbs
 
 
50J / 37 ft/lbs
 
 
60J / 44 ft/lbs
 
 
Not specified
 
Required energy with regulator
Required energy with regulator    * Required
 
7,5J / 5,5 ft/lbs
 
 
12J / 9 ft/lbs
 
 
16J / 12 ft/lbs
 
 
21J / 15,5 ft/lbs
 
 
27J / 20 ft/lbs
 
 
33J / 24 ft/lbs
 
 
40J / 30 ft/lbs
 
 
45J / 33 ft/lbs
 
 
50J / 37 ft/lbs
 
 
60J / 44 ft/lbs
 
 
Not specified
 
  
  Quantity: