Evanix Rex model with airtube

New

This Airgun Regulator is vented to atmosphere, but without drilling in the airtube. Simple installation.

More details

84,00 €

- +

  • High precion of regulation

  • Unique technologic solution

  • You buy directly from the manufacturer

  • 2 years warranty

  • Free shipping all over the world

  • Reviews
  • Video
  • Results
  • Insctruction

No customer comments for the moment. Login

Write a review

Evanix Rex model with airtube

Evanix Rex model with airtube

This Airgun Regulator is vented to atmosphere, but without drilling in the airtube. Simple installation.

Write a review

Evanix Rex regulator video installation

Evanix REX regulator results for .30 cal with JSB 2.9g

Fill pressure 220 bar

.30 JSB 2.9g is result without regulator

Regulator 12cc is regulator without extra airchamber

Regulator 20cc is regulator with one extra airchamber

Regulator 28cc is regulator with two extra airchambers

Regulator is sold with one airchamber, if you have big bore caliber and want one extra airchamber fill this info in note next to order. Airchamber cost 10 euro.

It is appropriate before reading the instructions look at the video instructions and then read the instructions for avoiding common mistakes during installation Evanix REX ( models with airtube )

Unscrew airtube + cleaning

Drain all air from airtube. Unscrew airtube from airgun and clean o-ring and inside of the airtube. For cleaning we use a foam or lint free cloth. It is good to wash out the inside of the airtube with degreaser, or technical petrol, etc..

Mount regulator

Remove the O-ring from valve. Unscrew hexagonal plug from valve and screw new one which was sent with regulator.

Spray regulators o-ring from outer side with silicone spray. Insert regulator and airchamber into airtube so that you see half of threads inside of airtube. Screw valve back in airtube, by screwing valve we get regulator into correct position. Dont screw plug to the max, but leave a gap (between plug and airtube) about 0.1-0.5 mm

Filling and draining air

Fill airtube with air through quick fill.

Seting regulátor

The pressure setting is done by using a flat screwdriver in the upper part of the regulator.  When we setting regulator we rotate with  inside plastic screw with groove. The output pressure is showed by location colored grooves on the inner plastic screw. The total rotation range of the output pressure is in the range from 100 to 150 bar and is approximately 3/4 turn.

Scale is starting on 100 bar (green color) and ends on 150 bar (red color). Scale is only approximate and course times may change slightly due to fatigue disc springs. Fill the airtube to the maximum pressure which is mentioned by manufacturer.

Shipment contains

  • Regulator
  • 2 spare o-rings.

Warning

You must keep maximum cleanness in the entire pressure system (airtube and outer o-rings). Do not disassemble the regulator without previous approval, which will be awarded based on e-mail correspondence, where you provide the reason why it would be necessary to disassemble the regulator. In the case of breach this procedure you may damage the regulator function (fully assembled regulator is not simple and it is necessary to follow the correct procedure). For these reasons, the disassembly without previous consent,or failure exact installation procedure can not claim the warranty. Since regulator is not original part from the manufacturer’s, installation is on your own responsibility.

 

 

Product options note

These data is only information for us, not mandatory values. For example, if your rifle is currently set on 16J, then you can not with regulator expects higher energy than 16J. The regulator can never increase energy!

For more information, please read FAQ section or contact us by e-mail.

Output pressure we set according to requirements the power rifle with the regulator. If you want a specific output pressure so indicate that in notes for orders.

If you do not know any product options, or you are unsure so please state this in the notes for orders.

Product Options
Full name of airgun model
Full name of airgun model    * Required
Full name 
 
 
* Required
Airgun model
Airgun model    * Required
 
US
 
 
UK
 
 
EU
 
 
AUS
 
 
ASIA
 
Caliber
Caliber    * Required
 
.177 /4.5mm
 
 
.20 /5.0mm
 
 
.22/5.5mm
 
 
.25/6.35mm
 
 
.35/ 9mm
 
Actual measured energy or energy given by the manufacturer
Actual measured energy or energy given by the manufacturer    * Required
 
7,5J / 5,5 ft/lbs
 
 
12J / 9 ft/lbs
 
 
16J / 12 ft/lbs
 
 
21J / 15,5 ft/lbs
 
 
27J / 20 ft/lbs
 
 
33J / 24 ft/lbs
 
 
40J / 30 ft/lbs
 
 
45J / 33 ft/lbs
 
 
50J / 37 ft/lbs
 
 
60J / 44 ft/lbs
 
 
Not specified
 
Required energy with regulator
Required energy with regulator    * Required
 
7,5J / 5,5 ft/lbs
 
 
12J / 9 ft/lbs
 
 
16J / 12 ft/lbs
 
 
21J / 15,5 ft/lbs
 
 
27J / 20 ft/lbs
 
 
33J / 24 ft/lbs
 
 
40J / 30 ft/lbs
 
 
45J / 33 ft/lbs
 
 
50J / 37 ft/lbs
 
 
60J / 44 ft/lbs
 
 
Not specified
 
  
  Quantity: