It is a simple installation without adjustments on rifle, so everything can be returned back. All you need to do is unscrew the valve body from bottle (before screwing launch air). You need suitable stick and vise. Then screw regulator between the bottle and valve. Regulator with vented to atmosphere.
The position of the manometer and quick fill pin can be selected before pressurizing. To fulfill the need to purchase painball coupling , which is the same as marauder or other rifle. After installing the regulator NEVER fill the old way, through the valve. At fill always open the valve bottle slowly and do not fill too quickly.
After installing the regulator NEVER fill throught by valve on the airgun, only by quick fill on regulator.
For the filling you must purchase paintball coupling, which is the same as gun marauder or more.
Regulator can be used in new version with spinlock, manometr on airgun will show you regulated pressure, manometr on regulator will show you pressure on airtube. Always fill throught pin on regulator.
Do not use pin as lever for tightening regulator. For that is added screw in spare o-rings .
!!! Dont forget turn on NOTE in youtubevideo. This notes are important for the correct installation , so you can avoid frequent mistakes !!
Installation video is identical with the installation as for gunpower rifle
Some regulator video test with chrono
Regulator set to 160Bar
Regulator set to 170Bar
Regulator set to 105Bar
We do Hydro test on regulator body to 380bar
What to do when your output pressure increasing over time? This is most likely caused by dirt on o-ring on plastic screw.
In this video is shown how remove dirt and replace o-ring.
It is appropriate before reading the instructions look at the video instructions and then read the instructions for avoiding common mistakes during installation GunPower
Unscrew airtube + cleaning
Before removing plug we need drain all air from airtube.
Screw regulátor on plug. We have to be sure that the regulator has in the groove the o-ring. Then screw the regulator back into the bottle and check again presence of o-ring in the neck of the bottle. Check the o-rings (cleanliness, if they are without damage) on filling pin and manometer. Pin and manometr screw on regulator only with fingers, screw them so much that the upper larger cylinder of manometr and pin are touching regulator perimeter. Slot for pin and manometer can be changed depending on where you get more comfortable with his position, You can make a small correction and and unscrew bottle littlebite (no need to complete attachment to the wall). When your manometer and pin has bad position you can insert black nylon ring in place o-ring. This changes the position after screwing.
Filling and draining air
NEVER fill air through valve on airtube, but always fill through quick fill on regulátor. If is all ok, connect Paintball coupler and fill airtube. Be sure that paintball coupler ball lock is fall in. First filling make slowly around 2-3 per second Bar. According to the type of bottle can be pressurized up to 250 bar (3600 PSI). After filling to set pressure drain air from hose and disconnect paintball coupler.
The pressure setting is done by using a flat screwdriver in the upper part of the regulator. When we setting regulator we rotate with inside plastic screw with groove. The output pressure is showed by location colored grooves on the inner plastic screw. The total rotation range of the output pressure is in the range from 100 to 150 bar and is approximately 3/4 turn.
Scale is starting on 100 bar (green color) and ends on 150 bar (red color). Scale is only approximate and course times may change slightly due to fatigue disc springs. Fill the airtube to the maximum pressure which is mentioned by manufacturer.
- Pin a manometr
- 2 pieces 2×1 o-rings for bolt on pin
- 3pieces 4×1 for pin and manometr
- 1piece 19×2,5 seal between the valve and the regulator body
You must keep maximum cleanness in the entire pressure system (airtube and outer o-rings). Do not disassemble the regulator without previous approval, which will be awarded based on e-mail correspondence, where you provide the reason why it would be necessary to disassemble the regulator. In the case of breach this procedure you may damage the regulator function (fully assembled regulator is not simple and it is necessary to follow the correct procedure). For these reasons, the disassembly without previous consent,or failure exact installation procedure can not claim the warranty. Since regulator is not original part from the manufacturer’s, installation is on your own responsibility.
Graphs for Output pressure 100bar .22 weight 18.1grain (1.175g)
Output pressure 150bar .22 weight 18.1grain (1.175g)
Output pressure 170bar .22 weight 25.4 grain ( 1.65g)
*Note All measurement are made on model SSS gunpower with barrel length 600mm (23,6″). For shorter barrel can by results different ( lower power or lower the number of shots with the same power )