Gamo Coyote

New

No drilling in the tank. Unscrew the air tube cap. Insert regulator on bottom of air tube and then screw back in airtube. Gamo coyote use same airtube like BSA Bucaneer. Maybe other Gamo airgun using same airtube too .

 89.00 USD

More details

79,00 €

- +

  • High precion of regulation

  • Unique technologic solution

  • You buy directly from the manufacturer

  • 2 years warranty

  • Free shipping all over the world

  • Reviews
  • Video
  • Instruction
  • Results
  • Volume discounts

No customer comments for the moment. Login

Write a review

Gamo Coyote

Gamo Coyote

No drilling in the tank. Unscrew the air tube cap. Insert regulator on bottom of air tube and then screw back in airtube. Gamo coyote use same airtube like BSA Bucaneer. Maybe other Gamo airgun using same airtube too .

 89.00 USD

Write a review

!!!Dont forget turn on NOTE in youtubevideo. This notes are important for the correct installation , so you can avoid frequent mistakes !!!

Gamo coyote using same airtube like BSA bucaneer

Video Installation is simillar with BSA bucanner:

Correct clean air tube and regulator:

Setting output pressure on regulator:

What to do when your output pressure increasing over time? This is most likely caused by dirt on o-ring on plastic screw.

In this video is shown how remove dirt and replace o-ring . In video is used Gunpower regulator. Procedure is same for others regulator.

It is appropriate before reading the instructions look at the video instructions and then read the instructions for avoiding common mistakes during installation

Gamo Coyote

1)   Unscrew airtube
2)   Mount regulator
3)   Set regulator
4)   Shipment contains

1) Before removing plug we need drain all air from airtube, we can shoot without pellets for drain air. Unscrew couple between airtube and barrel, than remove the plug itself. For unscruwing  plug we can use mounting sitck as lever.

2) Screw the installation stick to the regulator and check o-ring, if is clean and not damaged. Spray o-ring with silicone spray for preventing any damage. Push regulator to the bottom of airtube then unscrew mounting stick and screw quickfill plug back .

3) The pressure setting is done by  using a flat screwdriver in the upper part of the regulator.  When we setting regulator we rotate with  inside plastic screw with groove. The output pressure is showed by location colored grooves on the inner plastic screw. The total rotation range of the output pressure is in the range from 100 to 150 bar and is approximately one  turn.
Scale is starting on 100 bar (green color) and ends on 150 bar (red color). Scale is only approximate and course times may change slightly due to fatigue disc springs. Fill the airtube to the maximum pressure which is mentioned by manufacturer.

4)Regulator
Installation stick

Warning: You must keep maximum cleanness in the entire pressure system (airtube and outer o-rings). Do not disassemble the regulator without previous approval, which will be awarded based on e-mail correspondence, where you provide the reason why it would be necessary to disassemble the regulator. In the case of breach this procedure you may damage the regulator function (fully assembled regulator is not simple and it is necessary to follow the correct procedure). For these reasons, the disassembly without previous consent,or failure exact installation procedure can not claim the warranty. Since regulator is not original part from the manufacturer’s, installation is on your own responsibility.

Big thanks for results to Phil from Wales.

Gamo results

Quantity Discount You Save
2 -1 731,00 € Up to -3 462,00 €

Product options note

These data is only information for us, not mandatory values. For example, if your rifle is currently set on 16J, then you can not with regulator expects higher energy than 16J. The regulator can never increase energy!

For more information, please read FAQ section or contact us by e-mail.

Output pressure we set according to requirements the power rifle with the regulator. If you want a specific output pressure so indicate that in notes for orders.

If you do not know any product options, or you are unsure so please state this in the notes for orders.

Product Options
Full name of airgun model
Full name of airgun model    * Required
Full name 
 
 
* Required
Airgun model
Airgun model    * Required
 
US
 
 
UK
 
 
EU
 
 
AUS
 
 
ASIA
 
Caliber
Caliber    * Required
 
.177 /4.5mm
 
 
.20 /5.0mm
 
 
.22/5.5mm
 
 
.25/6.35mm
 
 
.35/ 9mm
 
Actual measured energy or energy given by the manufacturer
Actual measured energy or energy given by the manufacturer    * Required
 
7,5J / 5,5 ft/lbs
 
 
12J / 9 ft/lbs
 
 
16J / 12 ft/lbs
 
 
21J / 15,5 ft/lbs
 
 
27J / 20 ft/lbs
 
 
33J / 24 ft/lbs
 
 
40J / 30 ft/lbs
 
 
45J / 33 ft/lbs
 
 
50J / 37 ft/lbs
 
 
60J / 44 ft/lbs
 
 
Not specified
 
Required energy with regulator
Required energy with regulator    * Required
 
7,5J / 5,5 ft/lbs
 
 
12J / 9 ft/lbs
 
 
16J / 12 ft/lbs
 
 
21J / 15,5 ft/lbs
 
 
27J / 20 ft/lbs
 
 
33J / 24 ft/lbs
 
 
40J / 30 ft/lbs
 
 
45J / 33 ft/lbs
 
 
50J / 37 ft/lbs
 
 
60J / 44 ft/lbs
 
 
Not specified
 
  
  Quantity: