P12 bullpup

New

Regulator with vented to atmosphere, but without drilling in the tank.

 89.00 USD

More details

79,00 €

- +

  • High precion of regulation

  • Unique technologic solution

  • You buy directly from the manufacturer

  • 2 years warranty

  • Free shipping all over the world

  • Reviews
  • Video
  • Instruction
  • Results
  • Volume discounts

No customer comments for the moment. Login

Write a review

P12 bullpup

P12 bullpup

Regulator with vented to atmosphere, but without drilling in the tank.

 89.00 USD

Write a review

!!! Dont forget turn on NOTE in youtubevideo. This notes are important for the correct installation , so you can  avoid frequent mistakes !!!

Install regulator

Setting output pressure on regulator

What to do when your output pressure increasing over time? This is most likely caused by dirt on o-ring on plastic screw.

In this video is shown how remove dirt and replace o-ring . In video is used Gunpower regulator. Procedure is same for others regulator.

It is appropriate before reading the instructions look at the video instructions and then read the instructions for avoiding common mistakes during installation

Installation is same as for all others vented regulators. Empty all presure from airtube, unscrew airtube from valve, remove o-ring from valve, put regulator in airtube and screw valve back on airtube. Do not screw airtube on valve fully leav small gap between them (0,2 mm +-) by doing this and removing o-ring from valve you created venting hole without need for any drilling in airtube.

P12 bullpup without regulator with JSB heavy 0.67g

P12 bullpup with regulator set on 100bar with JSB heavy 0.67g

P12 bullpup with regulator set on 125 bar with JSB heavy 0.67g

Compared with and without regulator

Quantity Discount You Save
2 -1 731,00 € Up to -3 462,00 €

Product options note

These data is only information for us, not mandatory values. For example, if your rifle is currently set on 16J, then you can not with regulator expects higher energy than 16J. The regulator can never increase energy!

For more information, please read FAQ section or contact us by e-mail.

Output pressure we set according to requirements the power rifle with the regulator. If you want a specific output pressure so indicate that in notes for orders.

If you do not know any product options, or you are unsure so please state this in the notes for orders.

Product Options
Full name of airgun model
Full name of airgun model    * Required
Full name 
 
 
* Required
Airgun model
Airgun model    * Required
 
US
 
 
UK
 
 
EU
 
 
AUS
 
 
ASIA
 
Caliber
Caliber    * Required
 
.177 /4.5mm
 
 
.20 /5.0mm
 
 
.22/5.5mm
 
 
.25/6.35mm
 
 
.35/ 9mm
 
Actual measured energy or energy given by the manufacturer
Actual measured energy or energy given by the manufacturer    * Required
 
7,5J / 5,5 ft/lbs
 
 
12J / 9 ft/lbs
 
 
16J / 12 ft/lbs
 
 
21J / 15,5 ft/lbs
 
 
27J / 20 ft/lbs
 
 
33J / 24 ft/lbs
 
 
40J / 30 ft/lbs
 
 
45J / 33 ft/lbs
 
 
50J / 37 ft/lbs
 
 
60J / 44 ft/lbs
 
 
Not specified
 
Required energy with regulator
Required energy with regulator    * Required
 
7,5J / 5,5 ft/lbs
 
 
12J / 9 ft/lbs
 
 
16J / 12 ft/lbs
 
 
21J / 15,5 ft/lbs
 
 
27J / 20 ft/lbs
 
 
33J / 24 ft/lbs
 
 
40J / 30 ft/lbs
 
 
45J / 33 ft/lbs
 
 
50J / 37 ft/lbs
 
 
60J / 44 ft/lbs
 
 
Not specified
 
  
  Quantity: