Air Arms S410 Beech classic regulator

Air Arms S410 Beech classic regulator
search
  • Air Arms S410 Beech classic regulator
  • AirArms S400, S410, S510, TDR and similar models
  • AirArms S400, S410, S510, TDR and similar models
  • Air Arms S410 Beech classic regulator
AA-RE-001-007

The easiest and fastest installation regulator in the world.

This Airgun Regulator is the same for all others models us, for example, S400, S410, S510, TDR. No drilling in the tank. Manometer on airgun shows regulated pressure. Simple installation. Quickfill with manometer was added in section others accessories.

  • 250 char. max
Caliber: .177 /4.5mm
Required energy with regulator: 7,5J / 5,5 ft/lbs
Kč2,200.00
Quantity

visa

Airgun regulator for Air Arms S410 Beech classic

Regulator can be used in :

S300 Carbine / S300 Classic

S310 Carbine / S310 Classic

S400 Carbine / S400 Classic

S410 Carbine / S410 Classic

S500 Carbine / S500 Classic

S510 Carbine / S510 Classic

TDR

Videos for installation and proper use regulator in the airgun AirArms classic

AirArms Classic version video installation

Setting output pressure on regulator

What to do when your output pressure increasing over time? This is most likely caused by dirt on o-ring on plastic screw.

In this video is shown how remove dirt and replace o-ring . In video is used Gunpower regulator. The procedure is the same for other regulators.

Video how to take regulator out of regulator body

Installation instuction for AirArms classic air rifle pressure regulator

NOTE: Few customers wrote to us that in the last version of AA classic was added under valve spring iron roller. This roller has to be removed to get valve spring preload right, in some cases airtube could not be filled, there was airleak around valve when this roller was not removed.

It is appropriate before reading the instructions look at the video instructions and then read the instructions for avoiding common mistakes during installation AirAmrs

How to mount Altaros regulator

Drain all air from airtube and unscrew coupler between airtube and barrel. Unscrew airtube and unscrew manometer too, deflect manometer and unscrew bolt under him.
Replace original airchamber with new one which is sent with regulator. Screw this new airchamber in such depth that from top of the valve to top of this new airchamber is distance 7,9mm.
By doing this and screwing it in right position you set optimal spring preload. Screw small bolt under manometer so new airchamber can not be unscrewed anymore. Put manometer back in original position and screw manometer holder. Check inside of airtube and o-ring on regulator, all should be clean without any damage. Spray thread inside of airtube and o-ring on regulator with silicone spray. Push regulator inside airtube (brass regulator towards quickfill). Then push airchamber in airtube too. It should be pushed in such depth that you see approximately half of inner thread inside of airtube. Take airchamber out and put it next to valve, attach airtube and start screwing airtube back on airgun valve. By screwing it back ( with airchamber inside ) you get your regulator in the right position. Installation is complete.

Before filling is needed stretch cocking lever rifle, otherwise air will still pass through the barrel. When filling is necessary to fully open the valve diving bottle until in airtube is 70bar or more, then it is possible to fulfill the normal speed.

Setting pressure of airgun regulator

Altaros regulator output pressure can be set from 100bar (1450 PSI) to 150bar (2200 PSI). For a quick setting is on regulator engraved scale according to which the desired output pressure can be set. The total scale range of 100-150bar corresponds to approximately 1/2- turn. Unscrewing, or screwing setting screw more than 1 turn may result in a malfunction of the regulation and scale will not show you regulated pressure. Groove on red marked half of setting plastic screw represents pointer which shows you currently set pressure on the scale. To change the pressure on regulator, just simply rotate the set screw with the flat screwdriver in the appropriate direction according to regulator scale.
Regulator pressure scale with three different settings


Recommended output pressure to 16 J is in the range of 100 to 120 bar.

Altaros regulator shipment contains

  • Airarms Regulator
  • Brass handle for regulator
  • Airchamber
  • Spare o-rings

Recommended settings rifle after installing the regulator. Set a side screw that restricts the flow through channel in the barrel to achieve minimum consumption at 16J.

Remove the side screw, which is interfering in the channel and then try screw it little by little back until it begins to decrease Shooting speed.

Warning: 

Never unscrew regulator brass screw plugs! If you do so the regulator immediately stops working and repair is only possible at the manufacturer!

You must keep maximum cleanness in the entire pressure system (airtube and outer o-rings).

The disassembly of the internal parts regulator or failure at the exact installation procedure means that you can not claim the warranty. Since the regulator is not original part from the manufacturer’s, installation is on your own responsibility.

Results with installed regulator in air gun AirArms classic

Measurements were performed with a small airtube. With larger airtube will by the number of shots higher. Around 90-120 shots.

Average 221,6ms
Min 220,1ms
Max 223,1ms
Difference 3ms
Shots 67
Power 16J

Average 213,3ms
Min 212,2ms
Max 214,7ms
Difference 2,5ms
Shots 79
Power 15,2J

You might also like