Daystate Wolverine airgun regulator

Daystate Wolverine
search
  • Daystate Wolverine
  • Daystate Wolverine
CA-RE-026-001

This Airgun Regulator is vented to atmosphere, but without drilling in the tank. Simple installation. Just unscrew the air tube from airgun body.

  • 250 char. max
Caliber: .177 /4.5mm
Required energy with regulator: 7,5J / 5,5 ft/lbs
Kč2,200.00
Quantity

visa

This Airgun Regulator is vented to atmosphere, but without drilling in the tank. Simple installation. Just unscrew the air tube from airgun body.

Videos for installation and proper use regulator in the airgun Daystate Wolverine

Daystate Wolverine video Installation

Setting output pressure on regulator

What to do when your output pressure increasing over time? This is most likely caused by dirt on o-ring on plastic screw.

In this video is shown how to remove dirt and replace o-ring. In video is used Gunpower regulator. Procedure is the same for other regulators.

Video how to take regulator out of regulator body

Correct clean air tube and regulator

Installation instructions for Daystate Wolverine air rifle pressure regulator

It is appropriate before reading the instructions look at the video instructions and then read the instructions for avoiding common mistakes during installation

Daystate Wolverin

1) Unscrewing the airtube + cleaning

Drain all air from airtube. Remove coupling between airtube and barrel. Unscrew airtube from airgun and clean o-ring and inside of the airtube. For cleaning, we use a foam or lint-free cloth. It is good to wash out the inside of the airtube with degreaser, or technical petrol, etc.

2) Mounting of the regulator

Remove the O-ring from plug. Spray regulators o-ring from the outer side with silicone spray. Insert regulator into airtube so that it is possible to screw the brass plug and check the presence of the lower O-ring in the groove. By screwing plug we get regulator into the correct position. Don't screw plug to the max, but leave a gap (between plug and airtube) about 0.5 mm

3) Filling and draining air

Fill airtube with air through quick fill. After proper installation should gauge on airgun show regulated pressure, for the filling always use a filling set with an external gauge so that you have an overview of the real pressure in the airtube.

4) Setting pressure of airgun regulator

Altaros regulator output pressure can be set from 100bar (1450 PSI) to 150bar (2200 PSI) and after consultation of up to 170bar (2500PSI) which corresponds to the rotation of the screw behind value 150bar so that the line of the screw is pointing to the letter R. For a quick setting is on regulator engraved scale according to which the desired output pressure can be set. The total scale range of 100-150bar corresponds to approximately 2/3 turn Unscrewing, or screwing setting screw more than 1 turn may result in a malfunction of the regulation and scale will not show you regulated pressure. Groove on red marked half of setting plastic screw represents pointer which shows you currently set pressure on the scale. To change the pressure on regulator, just simply rotate the set screw with the flat screwdriver in the appropriate direction according to regulator scale.


Regulator pressure scale with three different settings


In this picture you will find an old scale (set at 100 bar), which we no longer sell.

The scale is starting on 100 bar (green color) and ends on 150 bar (red color). The scale is only approximate and course times may change slightly due to fatigue disc springs. Fill the airtube to the maximum pressure which is mentioned by the manufacturer.

5) Shipment contains

Regulator

2 spare o-rings.

Results with installed regulator in air gun Wolverine

Wolverine regulator set on 155 bar 5.5mm pellets 1.18g

Regulator used with different screw-on striker ( for limited operation length of the firing pin )

Altaros daystate woverine regulator results

Wolverine regulator set on 170BAR 5.5mm pellets 1.65g monster

Regulator used with different screw-on striker ( for limited operation length of the firing pin )

Wolverine compared with and without regulator .22 pellets 1.65g

Altaros daystate woverine regulator results comapred

Wolverine new bolt to hammer for more limited travel

New wolverine bolt

Wolverine new bolt ( this bolt is sent with regulator )

New wolverine bolt

Great video from Gregor about Wolverine 303. 30 caliber with/without regulator and other modification

Results from Gregor:

Daystate Wolverine 303 Unregulated JSB .30 - 50,15 grain

Daystate Wolverine 303 Regulated 155 bar - JSB .30 - 50,15 grain Modified

Daystate Wolverine 303 Regulated 170 bar - JSB .30 - 50,15 grain

You might also like