SPA Artemis P15

Diana Outlaw airgun regulator
search
  • Diana Outlaw airgun regulator
  • SPA Artemis P15
  • SPA Artemis P15
  • Diana Outlaw airgun regulator
CA-RE-023-004

No drilling into the airtube. Installation is very simple.

Drain air from the airtube, unscrew the cairtube from valve , unscrew the original regulator from the valve and replace it with the Altaros regulator. Screw the airtube back onto the valve and the installation is complete.

  • 250 char. max
Caliber: .177 /4.5mm
Required energy with regulator: 7,5J / 5,5 ft/lbs
Kč2,200.00
Quantity

visa

Airgun regulator for SPA Artemis P15

This Airgun Regulator is vented to atmosphere, but without drilling in the airtube. Very simple installation.

Videos for installation and proper use regulator in the airgun SPA Artemis P15

Video installation for SPA Artemis P15.

Setting output pressure on regulator

Correct cleaning of air tube and regulator

What to do when your output pressure increasing over time? This is most likely caused by dirt on o-ring on plastic screw.

In this video is shown how remove dirt and replace o-ring . In video is used Gunpower regulator. Procedure is same for other regulators.

Video how to take the regulator out of regulator body

Installation instructions for SPA Artemis P15 air rifle 

Unscrew airtube + cleaning

Drain all air from airtube. Remove coupling between airtube and barrel. Unscrew airtube from airgun and clean o-ring and inside of the airtube. For cleaning, we use a foam or lint free cloth. It is good to wash out the inside of the airtube with degreaser, or technical petrol, etc..

Mount Altaros regulator

Unscrew the original regulator from the valve and replace it with our Altaros regulator.

Spray regulators o-ring from the outer side with silicone spray. It is also good to spray airtube inner thread too.

Insert airtube around regulator on the valve and screw it fully.

Regulator installation is finished.

Filling air

Fill airtube with air through quick fill with pressure recommended by manufacturer.

Setting pressure of airgun regulator

Altaros regulator output pressure can be set from 100bar (1450 PSI) to 150bar (2200 PSI) and after consultation of up to 170bar (2500PSI) which corresponds to the rotation of the screw behind value 150bar so that the line of the screw is pointing to the letter R. For a quick setting is on regulator engraved scale according to which the desired output pressure can be set. The total scale range of 100-150bar corresponds to approximately 2/3 turn Unscrewing, or screwing setting screw more than 1 turn may result in a malfunction of the regulation and scale will not show you regulated pressure. Groove on red marked half of setting plastic screw represents pointer which shows you currently set pressure on the scale. To change the pressure on regulator, just simply rotate the set screw with the flat screwdriver in the appropriate direction according to regulator scale.


Regulator pressure scale with three different settings


In this picture you will find an old scale (set at 100 bar), which we no longer sell.

Shipment contains

  • Altaros Regulator
  • Regulator airchamber
  • 2 spare o-rings.

Warning

You must keep maximum cleanness in the entire pressure system (airtube and outer o-rings). Do not disassemble the regulator without previous approval, which will be awarded based on e-mail correspondence, where you provide the reason why it would be necessary to disassemble the regulator. In the case of breach this procedure you may damage the regulator function (fully assembled regulator is not simple and it is necessary to follow the correct procedure). For these reasons, the disassembly without previous consent, or failure exact installation procedure can not claim the warranty. Since regulator is not original part from the manufacturer’s, installation is on your own responsibility.

Results with installed regulator in air gun Diana Outlaw.

5,5 caliber     18,1 grain Jumbo Heavy   Regulator set on 100 bar

Diana Outlaw results with Altaros regulator set on 100 bar

5,5 caliber    18,1 grain Jumbo Heavy    Regulator set on 130 bar

You might also like