Benjamin Armada airgun regulator

Benjamin Marauder
search
  • Benjamin Marauder
CA-RE-005-002

The easiest and fastest installation regulator in the world.

Regulator for Benjamin Armada is same like for Benjamin Marauder

This Airgun Regulator does not need drilling in the tank. No degrade air gauge (gauge shows pressure in air tank, not regulated pressure). Simple installation.

  • 250 char. max
Caliber: .177 /4.5mm
Required energy with regulator: 7,5J / 5,5 ft/lbs
€89.00
Quantity

visa

Airgun regulator for airgun Benjamin Armada

This Airgun Regulator does not need drilling in the tank. No degrade air gauge( gauge shows pressure in air tank, not regulated pressure). Simple installation.

Videos for installation and proper use regulator in the airgun Benjamin Armada

Benjamin Marauder video Installation



Video chrono test Benjamin marauder with regulator

Video chrono test Benjamin marauder with regulator

What to do when your output pressure increasing over time? This is most likely caused by dirt on o-ring on plastic screw.

In this video is shown how remove dirt and replace o-ring. In video is used Gunpower regulator. Procedure is the same for other regulators.

Installation instruction for Benjamin Armada air rifle pressure regulator

It is appropriate before reading the instructions look at the video instructions and then read the instructions for avoiding common mistakes during installation Benjamin Armada

Unscrew airtube

Before removing plug we need to drain all air from airtube, we can shoot without pellets for drain air. Unscrew coupler between airtube and barrel, then remove the plug itself. For removing plugs can be used pliers, or we can use coupling as lever.

Mount Altaros pressure regulator

After unscrewing plug is necessary to unscrew the handle with a manometer. Screw the installation stick to the regulator and check o-ring, if it is clean and not damaged. Spray o-ring with silicone spray for preventing any damage. Insert regulator handle to the bottom of airtube into the center hole. Regulator handle inserts only to a depth that you can see o-ring in the hole after removed manometer. Then pushing through manometer hole on o-ring ( with wrench, or other blunt object that will not cause damage to o-ring) and push regulator with circular motion to the bottom.

In the event of a leak around o-ring on the handle will unregulated pressure penetrates into regulated part and even the regulator is functioning properly, output pressure will be unregulated. This is the most common reason for poor consistency after installing the regulator, which is considered us malfunctioning regulator, which is bad consideration because error is in installation, or in uncleanness on the o-rings (which are between the regulator and the chamber, or between the chamber and handle of regulator). O-rings between the parts and regulator has to be easily squeezed between the walls (not too squashed). Remove the installation stick and screw the plug back into the airtube. Attach back coupling and everything is done. After installing regulator will be manometer still show pressure in airtube, not regulated pressure.

Guidance, extended manuals and video tutorials in English can be found on www.altaros.cz.

Setting pressure of airgun regulator

Altaros regulator output pressure can be set from 100bar (1450 PSI) to 150bar (2200 PSI). For a quick setting is on regulator engraved scale according to which the desired output pressure can be set. The total scale range of 100-150bar corresponds to approximately 1/2- turn. Unscrewing, or screwing setting screw more than 1 turn may result in a malfunction of the regulation and scale will not show you regulated pressure. Groove on red marked half of setting plastic screw represents pointer which shows you currently set pressure on the scale. To change the pressure on regulator, just simply rotate the set screw with the flat screwdriver in the appropriate direction according to regulator scale.
Regulator pressure scale with three different settings

Shipment contains

  • Regulator
  • Mounting stick
  • Spare o-rings

Warning: 

Never unscrew regulator brass screw plugs! If you do so the regulator immediately stops working and repair is only possible at the manufacturer! Regulator must be installed no later than six months after purchase. Ideally immediately upon delivery.

You must keep maximum cleanness in the entire pressure system (airtube and outer o-rings).

The disassembly of the internal parts regulator or failure at the exact installation procedure means that you can not claim the warranty. Since the regulator is not original part from the manufacturer’s, installation is on your own responsibility.

Internal composition of Benjamin Marauder

Results with installed regulator in air gun Benjamin Marauder

Regulator with airgun caliber 5.5, .22 JSB jumbo heavy, 18.1 grain (1.175gram) set on 140 bar

This is a rifle shipped to Europe with limited transfer port. The rifle supplied by the manufacturer for maximum power should give a better result.





Marauder without regulator

Graph comparing Benjamin marauder with and without regulator



Result for Regulator with airgun JSB heavy .177mm 0.67g set on 110 bar

Average 256,8ms
Difference 3,0ms
Shots 74
Power 22J

Benjamin marauder .25 1.65g compared without and with regulator set on 150 bar

Benjamin marauder results

You might also like