Daystate airgun regulator

Daystate (models with airtube)
search
  • Daystate ( model s kartuší )
  • Daystate ( model s kartuší )
  • Daystate ( model s kartuší )
  • Daystate (models with airtube)
CA-RE-012-001

This Airgun Regulator is vented to atmosphere, but without drilling in the tank. Simple installation.

 

  • 250 char. max
Caliber: .177 /4.5mm
Required energy with regulator: 7,5J / 5,5 ft/lbs
€69.42
Quantity

 

High precion of regulation

 

Regulators for PCP guns. Unique technologic solution

 

A proud sponsor of the World and European Championships in HFT. We support shooters from all over the world

 

A 2 year warranty is provided for the goods. Best quality guarantee from Altaros.

Airgun regulator for Daystate model with airtube

This Airgun Regulator is vented to atmosphere, but without drilling in the tank. Simple installation. Just unscrew the air tube from airgun body, insert regulator and screw it back. Full video installation is in section video. After installation manometer shows regulated pressure.

Videos for installation and proper use regulator in the airgun Daystate

Daystate video Installation

How to find out proper function of regulator.

It is same as with evanix ( manometr shows regulated pressure)

Correct clean air tube and regulator

Setting output pressure on regulator

Video how to take regulator out of regulator body

What to do when your output pressure increasing over time? This is most likely caused by dirt on o-ring on plastic screw.

In this video is shown how to remove dirt and replace o-ring. In video is used Gunpower regulator. Procedure is same for other regulators.

Installation instructions for Daystate air rifle pressure regulator

It is appropriate before reading the instructions look at the video instructions and then read the instructions for avoiding common mistakes during installation Daystate ( models with airtube )

Installation is simple! Drain all air form airtube then unscrew the valve body from the airtube. Spray o-rings with silicone oil, then push regulator inside airtube ( with circular movement like when you screwing valve, this movement will prevent damaging outer o-ring on regulator) in such depth so you can see ¾ thread inside airtube. Remove both o-rings from valve and screw valve back on airtube.By screwing plug back in airtube we get regulator into the correct position. Do not tight airtube and valve fully. Leave gap 0.2-0.5 mm between them, by doing this and removing o-rings from valve you creating venting hole ( with this is no drilling to airtube needed).

To keep installation as simple and clear as possible, we have created a series of titled videos to guide you step-by-step through the installation process; even if you’re not the technical type! Installation is in video section.

Setting pressure of airgun regulator

Altaros regulator output pressure can be set from 100bar (1450 PSI) to 150bar (2200 PSI) and after consultation of up to 170bar (2500PSI) which corresponds to the rotation of the screw behind value 150bar so that the line of the screw is pointing to the letter R. For a quick setting is on regulator engraved scale according to which the desired output pressure can be set. The total scale range of 100-150bar corresponds to approximately 2/3 turn Unscrewing, or screwing setting screw more than 1 turn may result in a malfunction of the regulation and scale will not show you regulated pressure. Groove on red marked half of setting plastic screw represents pointer which shows you currently set pressure on the scale. To change the pressure on regulator, just simply rotate the set screw with the flat screwdriver in the appropriate direction according to regulator scale.


Regulator pressure scale with three different settings


In this picture you will find an old scale (set at 100 bar), which we no longer sell.

Výsledky s nainstalovaným regulátorem tlaku ve vzduchové pušce Daystate

Výsledky jsou z Daystate hunstman regal 4.5 with Jsb exact 0,547 gram

Bez regulátoru



S regulátorem



Porovnání s a bez regulátoru

You might also like