Gunpower/ AirForce regulator for paintball bottle

Gunpower/ AirForce regulator for paintball bottle
search
  • Gunpower/ AirForce regulator for paintball bottle
  • Gunpower/ AirForce regulator for paintball bottle
  • Gunpower/ AirForce regulator for paintball bottle
  • Gunpower/ AirForce regulator for paintball bottle
  • Gunpower/ AirForce regulator for paintball bottle
  • Gunpower/ AirForce regulator for paintball bottle
CA-RE-020-001

Years proven regulators (since 2010) used by thousands of satisfied customers around the world.

The Airgun Regulator

On valve side has regulator (female) thread 18x 1,5 mm

On the side which is regulator screwed in airtank is (male)  thread is 5/8 x (18 UNF)

  • 250 char. max
Caliber: .177 /4.5mm
Required energy with regulator: 7,5J / 5,5 ft/lbs
€136.00
Quantity

visa

The Airgun Regulator is the same as regulator (with thread 18x 1,5 mm on valve) for rifles gunpower (AirForce Condore), Fx Royale 400 (FX Boss), Daystate air range, Edgar Brothers EB XVi, only difference is that this regulator can be mount in paintball bottle with thread 5/8 x (18UNF). It is a simple installation without adjustments on the rifle, so everything can be returned back. All you need to do is screw regulator between the bottle and airgun body. Regulator is vented to atmosphere. We are not selling Paintball botlles, only regulators! After installing the regulator NEVER fill by quick fill on the airgun, only by quick fill on regulator. For the filling, you must purchase paintball coupling, which is the same as gun marauder or more. Do not use a pin as a lever for tightening regulator. For that is added screw-in spare o-rings.

Installation is the same as with a normal air tank. Just use our o-rings on regulator, because original o-ring on paintball bottle is too thick and if you put it on regulator (part which is screwed in paintball bottle) manometer will not show you pressure.

Internal parts, regulation system is the same as with normal vented regulator, so results/ number of shots will depend on Paintball bottle size/max pressure etc. You can check results with original bottle on our web.

Videos for installation and proper use regulator in the airgun Gunpower/ AirForce regulator for paintball bottle

FX Airgun Royale 400 / FX Boss Installation


Video Installation for Sniper X2 bottle version which has airgun under barrel

What to do when your output pressure increasing over time? This is most likely caused by dirt on o-ring on plastic screw.

In this video is shown how to remove dirt and replace o-ring. In video is used Gunpower regulator. Procedure is the same for other regulators.

Video how to take regulator out of regulator body

Setting output pressure on regulator

Setting pressure of airgun regulator

Altaros regulator output pressure can be set from 100bar (1450 PSI) to 150bar (2200 PSI) and after consultation of up to 170 bar (2500 PSI) which corresponds to the rotation of the screw behind value 150bar so that the line of the screw is pointing to the letter R. For a quick setting is on regulator engraved scale according to which the desired output pressure can be set. The total scale range of 100-150bar corresponds to approximately 2/3 turn Unscrewing, or screwing setting screw more than 1 turn may result in a malfunction of the regulation and scale will not show you regulated pressure. Groove on red marked half of setting plastic screw represents pointer which shows you currently set pressure on the scale. To change the pressure on regulator, just simply rotate the set screw with the flat screwdriver in the appropriate direction according to regulator scale.


Regulator pressure scale with three different settings


In this picture you will find an old scale (set at 100 bar), which we no longer sell.

You might also like