Evanix Sniper x2 airgun regulator
The Airgun Regulator with simple installation without adjustments on the rifle, so everything can be returned back. All you need to do is unscrew the bottle from airgun body (before screwing launch air). Then screw regulator between the bottle and airgun body.
Download instructions: HERE
High precion of regulation
Regulators for PCP guns. Unique technologic solution
A proud sponsor of the World and European Championships in HFT. We support shooters from all over the world
A 2 year warranty is provided for the goods. Best quality guarantee from Altaros.
The Airgun Regulator is the same as a regulator for rifles gunpower, the only change is that in the package is also a nylon spacer ring, which is used in the case when gauge and filling pin is not in a good position. It is a simple installation without adjustments on rifle, so everything can be returned back. All you need to do is unscrew the bottle from airgun body (before screwing launch air). Then screw regulator between the bottle and airgun body. After installing the regulator NEVER fill by quick fill on the airgun, only by quick fill on regulator. For the filling, you must purchase paintball coupling, which is the same as gun marauder or more. Do not use the pin as a lever for tightening regulator. For that is added screw-in spare o-rings.
Videos for installation and proper use regulator in the airgun Evanix Sniper x2
Evanix Sniper x2
Setting output pressure on regulator
What to do when your output pressure increasing over time? This is most likely caused by dirt on o-ring on plastic screw.
Video how to take regulator out of regulator body
Installation instuction for Airgun Evanix Sniper x2rifle pressure regulator
in progress in the meantime you can look at the installation video in the video section.
Setting pressure of airgun regulator
Altaros regulator output pressure can be set from 100bar (1450 PSI) to 150bar (2200 PSI) and after consultation of up to 170bar (2500PSI) which corresponds to the rotation of the screw behind value 150bar so that the line of the screw is pointing to the letter R. For a quick setting is on regulator engraved scale according to which the desired output pressure can be set. The total scale range of 100-150bar corresponds to approximately 2/3 turn Unscrewing, or screwing setting screw more than 1 turn may result in a malfunction of the regulation and scale will not show you regulated pressure. Groove on red marked half of setting plastic screw represents pointer which shows you currently set pressure on the scale. To change the pressure on regulator, just simply rotate the set screw with the flat screwdriver in the appropriate direction according to regulator scale.
Regulator pressure scale with three different settings
In this picture you will find an old scale (set at 100 bar), which we no longer sell.
Results with installed regulator in air gun Evanix sniper X2
Evanix Sniper results without regulator and striking spring preload on minimum 5.5 1.03g
Evanix sniper results compared with and without regulator and striking spring preload on minimum 5.5 1.03g
Results from cutomers form United states, big thanks :
Hammer spring tension about 1.5 turn in
Created: 03/02/17 12:54 PM
Description: Evanix Sniper X2 (9mm)
Notes 1: ALTAROS Regulator @150bar
Notes 2: JSB 81.02 gr
Distance to Chrono(FT): 10.00
Ballistic Coefficient: 0.154
Bullet Weight(gr): 82.00
Temp: 80 °F
BP: 29.92 inHg
22 823 123.35 67.49
21 822 123.05 67.40
20 811 119.78 66.50
19 813 120.37 66.67
18 823 123.35 67.49
17 812 120.07 66.58
16 819 122.15 67.16
15 819 122.15 67.16
14 820 122.45 67.24
13 815 120.96 66.83
12 813 120.37 66.67
11 814 120.66 66.75
10 815 120.96 66.83
9 820 122.45 67.24
8 820 122.45 67.24
7 824 123.65 67.57
6 813 120.37 66.67
5 816 121.26 66.91
4 814 120.66 66.75
3 816 121.26 66.91
2 812 120.07 66.58
1 819 122.15 67.16