FX T12 airgun regulator

FX (models with airtube)
search
  • FX ( modely s kartuší )
  • FX ( modely s kartuší )
  • FX ( modely s kartuší )
  • FX (models with airtube)
CA-RE-015-002

The Airgun Regulator with vented to atmosphere, but without drilling in the tank. Simple installation.

  • 250 char. max
Caliber: .177 /4.5mm
Required energy with regulator: 7,5J / 5,5 ft/lbs
€89.00
Quantity

visa

Airgun regulator for FX T12

The Airgun Regulator with vented to atmosphere, but without drilling in the tank. Simple installation. Just unscrew the brass cap with valve and regulator only inserted into the tank and take out o-ring on brass body valve. This is all.

Videos for installation and proper use regulator in the airgun FX T12

FX video Installation

FX ranchero with Altaros regulator 4,5mm test with chrono, with switching velocity

What to do when your output pressure increasing over time? This is most likely caused by dirt on o-ring on plastic screw.

In this video is shown how to remove dirt and replace o-ring. In video is used Gunpower regulator. Procedure is the same for other regulators.

Video how to take regulator out of regulator body

Correct clean air tube and regulator

Setting output pressure on regulator

Installation instructions for FX T12 air rifle pressure regulator

It is appropriate before reading the instructions look at the video instructions and then read the instructions for avoiding common mistakes during installation FX

Unscrew airtube + cleaning

Before removing brass plug we need drain all air from airtube. After unscrewing the brass plug we clean o-ring and inside of the airtube. For cleaning we use a foam or lint-free cloth. It is good to wash out the inside of the airtube with degreaser, or technical petrol, etc..

Mount regulator

Remove the O-ring from brass plug. Spray regulators o-ring from the outer side with silicone spray. Insert regulator into airtube so that it is possible to screw the brass plug and check the presence of the lower O-ring in the groove. By screwing plug we get regulator into correct position. Don't screw plug to the max, but leave a gap (between plug and airtube) about 0.5 mm.

Filling and draining air

Fill airtube with air through quick fill. After proper installation should gauge on airgun show regulated pressure, for the filling always use a filling set with an external gauge, so that you have an overview of the real pressure in the airtube.

Setting pressure of airgun regulator

Altaros regulator output pressure can be set from 100bar (1450 PSI) to 150bar (2200 PSI) and after consultation of up to 170bar (2500PSI) which corresponds to the rotation of the screw behind value 150bar so that the line of the screw is pointing to the letter R. For a quick setting is on regulator engraved scale according to which the desired output pressure can be set. The total scale range of 100-150bar corresponds to approximately 2/3 turn Unscrewing, or screwing setting screw more than 1 turn may result in a malfunction of the regulation and scale will not show you regulated pressure. Groove on red marked half of setting plastic screw represents pointer which shows you currently set pressure on the scale. To change the pressure on regulator, just simply rotate the set screw with the flat screwdriver in the appropriate direction according to regulator scale.


Regulator pressure scale with three different settings


In this picture you will find an old scale (set at 100 bar), which we no longer sell.

Shipment contains

  • Altaros Regulator
  • 2 spare o-rings

Results with installed regulator in air gun FX T12

Fx Ranchero set on 122bar, airgun is set on minimum power



Fx Ranchero set on 122bar, airgun is set on middle power



Fx Ranchero set on 122bar, airgun is set on maximum power



Fx Ranchero without regulator

Fx Ranchero compare with and without regulator (red and purple), airgun is set on middle (green) and maximum (blue) power




You might also like