copy of Hatsan Flash/Vectis with steel/magnetic airtube
Unfortunately Hatsan started to produce versions Flash, Flashpup, Flashpup s generation 2, Flashpup S (synthetic), Vectis , Invader and other with two different airtubes.
The first version of the new Hatsan had a aluminum / non-magnetic airtube with an inner diameter of 26.5 mm and an outer diameter of 35.15 mm.
The second version of the new Hatsan had a steel / magnetic airtube with an inner diameter of 30 mm and an outer diameter of 35.01 mm.
This regulator version is for a magnetic airtube with Inner diameter of the airtube 30 mm and outer diameter of the airtube 35.01 mm. Check with a magnet that you have the correct airtube version.
High precion of regulation
Regulators for PCP guns. Unique technologic solution
A proud sponsor of the World and European Championships in HFT. We support shooters from all over the world
A 2 year warranty is provided for the goods. Best quality guarantee from Altaros.
Airgun regulator for Hatsan Flash PUP
This Airgun Regulator is vented to atmosphere, but without drilling in the airtube. Simple installation. Just unscrew the air tube from airgun body, unscrew valve, push regulator in, screw valve back. Then screw airtube back in airgun and installation is done.
Videos for installation and proper use regulator in the airgun Hatsan Flash PUP
Hatsan FLash installation in Magnetic airtube
Hatsan FLash installation in Not Magnetic airtube
How to find out proper function of regulator.
Setting output pressure on regulator
Correct clean air tube and regulator
What to do when your output pressure increasing over time? This is most likely caused by dirt on o-ring on plastic screw.
Video how to take regulator out of regulator body
Installation instruction for Hatsan Flash PUP air rifle pressure regulator
It is appropriate before reading the instructions look at the video instructions and then read the instructions for avoiding common mistakes during installation Hatsan Flash PUP
Unscrew airtube + cleaning
Drain all air from airtube. Remove coupling between airtube and barrel. Unscrew airtube from airgun and clean o-ring and inside of the airtube. For cleaning, we use a foam or lint-free cloth. It is good to wash out the inside of the airtube with degreaser, or technical petrol, etc..
Mount Altaros regulator
Remove the O-ring from plug. Spray regulators o-ring from the outer side with silicone spray. Insert regulator into airtube so that it is possible to screw the brass plug and check the presence of the lower O-ring in the groove. By screwing plug we get regulator into correct position. Don't screw plug to the max, but leave a gap (between plug and airtube) about 0.5 mm
Filling and draining air
Fill airtube with air through quick fill. After proper installation should gauge on airgun show regulated pressure, for the filling always use a filling set with an external gauge so that you have an overview of the real pressure in the airtube.
Setting pressure of airgun regulator
Altaros regulator output pressure can be set from 100bar (1450 PSI) to 150bar (2200 PSI) and after consultation of up to 170bar (2500PSI) which corresponds to the rotation of the screw behind value 150bar so that the line of the screw is pointing to the letter R. For a quick setting is on regulator engraved scale according to which the desired output pressure can be set. The total scale range of 100-150bar corresponds to approximately 2/3 turn Unscrewing, or screwing setting screw more than 1 turn may result in a malfunction of the regulation and scale will not show you regulated pressure. Groove on red marked half of setting plastic screw represents pointer which shows you currently set pressure on the scale. To change the pressure on regulator, just simply rotate the set screw with the flat screwdriver in the appropriate direction according to regulator scale.
Regulator pressure scale with three different settings
In this picture you will find an old scale (set at 100 bar), which we no longer sell.
- Altaros Regulator
- Regulator airchamber
- 2 spare o-rings.
You must keep maximum cleanness in the entire pressure system (airtube and outer o-rings). Do not disassemble the regulator without previous approval, which will be awarded based on e-mail correspondence, where you provide the reason why it would be necessary to disassemble the regulator. In the case of a breach of this procedure you may damage the regulator function (fully assembled regulator is not simple and it is necessary to follow the correct procedure). For these reasons, the disassembly without previous consent,or failure exact installation procedure can not claim the warranty. Since regulator is not original part from the manufacturer’s, installation is on your own responsibility.
Results with installed regulator in Hatsan FLash PUP
Hatsan Flash .177 regulator set on 115 bar , JSB Exact 0,547 g